The 8 pins PIC12F683 microcontroller is one of the smallest members of the Microchip 8-bit microcontroller families but equipped with powerful peripherals such as ADC and PWM capabilities. This make this tiny microcontroller is suitable for controlling the DC motor speed. In order to demonstrate the PIC12F683 capabilities and to make this tutorial more attractive, I decided to use the PIC12F683 microcontroller to generate simple and yet fascinating laser light show from a cheap keychain laser pointer.
The basic of laser light shown in many entertainments club or park mostly use two method; the first one is to beam the laser shower on the spectators and the second one is to display the laser drawing pattern on the screen. On this tutorial we are going to build the laser projector that displays the spirograph pattern on the screen using the tiny Microchip PIC12F683 microcontroller.
The principal of making the spirograph laser projector is to use at least two DC motors with the attached mirror on it, these mirrors then will deflect the laser beam from one DC motor mirror to the second DC motor mirror and then finally to the screen. By controlling each of the DC motors spinning speed we could generate a fascinating laser spirograph pattern on the screen as shown on this following picture.
The best way to control the DC motor speed is to use the PWM (pulse wave modulation) signal to drive the DC Motor and because we want to change the DC motor speed manually, therefore we need to use the trimport or potentiometer to control each of the DC motors speed. Hmm, this sound like an appropriate job for the microcontroller but could we use this tiny 8 pins PIC12F683 microcontroller to handle this task?
From the datasheet you will notice that the Microchip PIC12F683 microcontroller only has one PWM output (CCP1) and four ADC input channel (AN0, AN1, AN2 and AN3). Because we need two PWM output, therefore instead of using the PIC12F683 microcontroller build in PWM peripheral, in this tutorial I will show you how to generate the PWM signal base on the PIC12F683 microcontroller TIMER0 peripheral. The following is the complete electronic schematic for the laser projector project.
Ok before we go further with the detail; let’s list down the supporting peripherals needed to complete this laser projector project:
- Hot glue gun
- Keychain laser pointer or any available laser pointer
- 3xAA, 4.5 volt battery holder for powering the laser pointer, please use the same voltage rate used by your laser pointer.
- Two DC motor taken from the discarded PS2 Dual shock joystick
- Two toy’s car tire taken from tamiya racing car
- CD/DVD for the mirror, use a kitchen scissor to cut the CD/DVD into the two circle shape mirror with approximately 38 mm in diameter
- Some toys plastic bricks for holding the DC motor
- Breadboard
- Hardboard or acrylic is used for the base of our laser projector
- Double Tape
The following are the electronic parts and the software development tools that I used to make this laser projector project:
- Resistor: 330 (3), 1K (5) and 10K (1)
- Trimport: 10K (2)
- Capacitor: 100nF (2) and 10nF (1)
- One 100uH Inductor
- Two 1N4148 Diodes
- Two Blue and one Red Light Emitting Diode (LED)
- Two 2N2222A transistors
- One Mini Push Button Switch
- One Microchip PIC12F683 Microcontroller
- Microchip MPLAB v8.46 IDE (Integrated Development Environment)
- Microchip Macro Assembler MPASMWIN.exe v5.35, mplink.exe v4.35
- HI-TECH C Compiler for PIC10/12/16 MCUs (Lite Mode) V9.70
- Microchip PICKit3 Programmer (Firmware Suite Version: 01.25.20)
This project is aim as the continuing lessons to my previous posted blog Introduction to PIC Assembly Language Part-1 and Introduction to PIC Assembly Language Part-2, therefore I used the same PIC12F683 board presented in the part 2 which you could down load both of the electronic schematic and the PCB layout designed in Eagle CAD format. The other interesting feature of this laser projector project is; besides the PIC assembly code I also provide the C language version of this project for the C language lover and is compiled with the HI-TECH C Compiler (recently the HI-TECH Software has been acquired by Microchip). This C language version could be used for learning as well as the embedded system programming language comparison.
In this project I also use a new Microchip PICKit3 programmer but of course you could use the Microchip PICKit2 programmer to download the hex code to the PIC12F683 microcontroller flash.
The following is the Laser Projector code in PIC Assembly Language:
;******************************************************************************
; File Name : laserlight.asm
; Version : 1.0
; Description : Laser Light Show Project
; Author : RWB
; Target : Microchip PIC12F683 Microcontroller
; Compiler : Microchip Assembler (MPASMWIN.exe v5.35, mplink.exe v4.35)
; IDE : Microchip MPLAB IDE v8.46
; Programmer : PICKit3 (Firmware Suite Version: 01.25.20)
; Last Updated : 01 April 2010
; *****************************************************************************
#include __config (_INTRC_OSC_NOCLKOUT & _WDT_OFF & _PWRTE_OFF & _MCLRE_OFF & _CP_OFF & _IESO_OFF & _FCMEN_OFF)#define MAX_TMR0 0xFB
#define MAX_COUNT .200
#define MAX_DEBOUNCE 0x0A
#define MAX_TBLINDEX 0x0A; Define variables used
cblock 0x20
Delay:2 ; Define two registers for the Delay and Delay + 1
mode ; Operation Mode
pwm_count ; Hold the Main PWM Counter
pwm_m1 ; Hold the PWM width for Motor 1
pwm_m2 ; Hold the PWM width for Motor 2
keycount ; Debounce Count
tableindex ; Table Index for Auto PWM
endc; Define variable use for storing STATUS and WREG register
cblock 0x70 ; Use unbanked RAM, available both in Bank0 and Bank1
saved_w
saved_status
endc; Start the Light show Assembler Code here
org 0x00 ; We always start at flash address 0
goto Main ; Jump to Mainorg 0x04 ; 0x04: Start PIC Interrupt Address
PIC_ISR: ; Start the PIC Interrupt Service Routine
movwf saved_w ; Save Working Register
movf STATUS,w ; Save Status Register
movwf saved_status; Check the TIMER0 Interrupt here
btfss INTCON,T0IF
goto ExitISR ; If (T0IF != 1) then Exit ISR
bcf STATUS,RP0 ; Select Registers at Bank 0
incf pwm_count ; pwm_count++
movlw MAX_COUNT
subwf pwm_count,w ; if (pwm_count < MAX_COUNT) then CheckPWM
btfss STATUS,C ; else clear GP1 and GP2
goto CheckPWM
bcf GPIO,GP1 ; GPIO1=0
bcf GPIO,GP2 ; GPIO2=0
goto ExitPWMCheckPWM:
movf pwm_m1,w
subwf pwm_count,w
btfsc STATUS,Z ; if (pwm_count == pwm_m1) then Set GP1
bsf GPIO,GP1 ; Set GP1 Bit
CheckM2:
movf pwm_m2,w
subwf pwm_count,w
btfsc STATUS,Z ; if (pwm_count == pwm_m2) then Set GP2
bsf GPIO,GP2 ; Set GP2 bit
ExitPWM:
bcf INTCON,T0IF ; clear the TIMER0 interrupt flag
movlw MAX_TMR0
movwf TMR0 ; TMR0 = MAX_TMR0ExitISR:
movf saved_status,w
movwf STATUS ; Restore STATUS Register
swapf saved_w,f
swapf saved_w,w ; Restore W Register
retfie ; Return from InterruptMain:
bsf STATUS,RP0 ; Select Registers at Bank 1
movlw 0x70
movwf OSCCON ; Set the internal clock speed to 8 MHz
movlw 0x39 ; GP1 and GP2 Output, GP0,GP3,GP4 and GP5 as Input
movwf TRISIO ; TRISIO = 0x39
bcf STATUS,RP0 ; Select Registers at Bank 0
movlw 0x07
movwf CMCON0 ; Turn off Comparator (GP0, GP1, GP2)
clrf GPIO
; Now we Set the ADC Peripheral
bsf STATUS,RP0 ; Select Registers at Bank 1
movlw 0x79 ; Set AN0 (GP0) and AN3 (GP4) as Analog Input
movwf ANSEL ; Using the Internal Clock (FRC)
; Now we set the TIMER0 Peripheral
; TIMER0 Period = 1/FSOC x 4 x Prescale x TMR0
movlw 0x00 ; Use TIMER0 Prescaler 1:2, Internal Clock
movwf OPTION_REG ; OPTION_REG = 0x00bcf STATUS,RP0 ; Select Registers at Bank 0
movlw MAX_TMR0
movwf TMR0 ; TMR0=MAX_TMR0
; Initial the variables used
clrf mode ; Default mode = 0, Light Show Off
clrf pwm_count ; pwm_count = 0
clrf pwm_m1 ; pwm_m1 = 0
clrf pwm_m2 ; pwm_m2 = 0
clrf keycount ; keycount = 0
clrf tableindex ; tableindex = 0; Activate the Interrupt
bsf INTCON,GIE ; Enable Global InterruptMainLoop:
btfsc GPIO,GP5 ; Now we check the Button
goto CheckMode ; if (GP5 != 0) goto CheckMode
movlw 0x01
addwf keycount ; keycount=keycount + 1
movf keycount,w
sublw MAX_DEBOUNCE
btfss STATUS,C ; if (keycount > MAX_DEBOUNCE) goto KeyPressed
goto KeyPressed
goto CheckMode ; else CheckModeKeyPressed:
clrf keycount ; keycount=0
incf mode ; mode++
movlw 0x03
subwf mode,w ; W = mode - 0x03
btfsc STATUS,C ; if (mode >= 0x03)
clrf mode ; mode=0;
movlw 0x01 ; else check the mode
subwf mode,w
btfss STATUS,C ; if (mode >= 0x01) goto TurnOn
goto TurnOff ; else goto TurnOff
goto TurnOnTurnOff:
bcf INTCON,T0IE ; Disable TIMER0 Interrupt
clrf pwm_count ; pwm_count = 0
clrf pwm_m1 ; pwm_m1 = 0
clrf pwm_m2 ; pwm_m2 = 0
bcf GPIO,GP1
bcf GPIO,GP2
movlw .250
call DelayMs ; DelayMs(250)
movlw .250
call DelayMs ; DelayMs(250)
goto CheckModeTurnOn:
bsf INTCON,T0IE ; Enable TIMER0 Interrupt
CheckMode:
movlw 0x01
subwf mode,w
btfss STATUS,Z ; if (mode == 1) goto ShowMode1
goto CheckMode2
goto ShowMode1CheckMode2:
movlw 0x02
subwf mode,w
btfss STATUS,Z ; if (mode == 2) goto ShowMode2
goto KeepLoop
goto ShowMode2ShowMode1: ; Used ADC for PWM
movlw B'00000001' ; Left Justify and turn on the ADC peripheral, channel 0 (AN0)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 0 (AN0)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Loop
call Delay1msmovlw B'00000001' ; Left Justify and turn on the ADC peripheral, channel 0 (AN0)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 0 (AN0)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Loop
movf ADRESH,w ; Conversion Done, Read ADRESH
movwf pwm_m1 ; pwm_m1 = ADRESH
call Delay1ms
movlw B'00001101' ; Left Justify and turn on the ADC peripheral, channel 3 (AN3)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 3 (AN3)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Test
call Delay1msmovlw B'00001101' ; Left Justify and turn on the ADC peripheral, channel 3 (AN3)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 3 (AN3)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Test
movf ADRESH,w ; Conversion Done, Read ADRESH
movwf pwm_m2 ; pwm_m2 = ADRESH
call Delay1ms
goto KeepLoopShowMode2: ; Used Predefined Value for PWM
movf tableindex,w
call tablepwm1 ; Call tablepwm1
movwf pwm_m1 ; Assigned it to pwm_m1
movlw .30
call DelayMs ; DelayMs(30)
movf tableindex,w
call tablepwm2 ; Call tablepwm2
movwf pwm_m2 ; Assigned it to pwm_m2
movlw .30
call DelayMs ; DelayMs(30)incf tableindex ; tableindex++
movlw MAX_TBLINDEX
subwf tableindex,w
btfss STATUS,C ; if (tableindex >= 0x0A) then tableindex = 0
goto KeepLoop
clrf tableindex ; tableindex = 0KeepLoop:
goto MainLoop ; Goto MainLoop; Predefined value table for Automatic PWM
tablepwm1:
addwf PCL,f
retlw 0x10
retlw 0x5A
retlw 0x9A
retlw 0x20
retlw 0x40
retlw 0x8A
retlw 0x82
retlw 0x30
retlw 0x58
retlw 0xAAtablepwm2:
addwf PCL,f
retlw 0x70
retlw 0x8A
retlw 0x2A
retlw 0x30
retlw 0x1C
retlw 0x2A
retlw 0x4B
retlw 0xA0
retlw 0x18
retlw 0x2A;----------------- DelayMs: Millisecond Delay Subroutine ----------------------
; Paramater: WREG = delay amount in milisecond, max: 255 millisecond
DelayMs:
movwf Delay + 1
DelayLoop:
call Delay1ms
decfsz Delay + 1,f ; Decrease Delay + 1, If zero skip the next instruction
goto DelayLoop ; Not zero goto DelayLoop
return ; return to the caller;----------------- Delay1ms: 1 ms Delay Subroutine ---------------------------
Delay1ms: ; Total Delay: 1998 x 0.5us ~ 1 ms
movlw 0x99
movwf Delay
DelayLoop1:
decfsz Delay,f ; Decrease Delay, If zero skip the next instruction
goto DelayLoop1
DelayLoop2:
decfsz Delay,f ; Decrease Delay, If zero skip the next instruction
goto DelayLoop2 ; Not zero goto DelayLoop2
DelayLoop3:
decfsz Delay,f ; Decrease Delay, If zero skip the next instruction
goto DelayLoop3 ; Not zero goto DelayLoop2
return ; Return to the callerend
; EOF: laserlight.asm
The following is the Laser Projector Project code in C Language version:
// ***************************************************************************
// File Name : laserlight.c
// Version : 1.0
// Description : Laser Light Show Project
// Author : RWB
// Target : Microchip PIC12F683 Microcontroller
// Compiler : HI-TECH C PIC10/12/16 MCUs (Lite Mode) V9.70
// IDE : Microchip MPLAB IDE v8.46
// Programmer : PICKit3 (Firmware Suite Version: 01.25.20)
// Last Updated : 03 April 2010
// ***************************************************************************
#include /* PIC Configuration Bit:
** INTIO - Using Internal RC No Clock
** WDTDIS - Wacthdog Timer Disable
** PWRTEN - Power Up Timer Enable
** MCLRDIS - Master Clear Disable
** UNPROTECT - Code Un-Protect
** UNPROTECT - Data EEPROM Read Un-Protect
** BORDIS - Borwn Out Detect Disable
** IESODIS - Internal External Switch Over Mode Disable
** FCMDIS - Monitor Clock Fail Safe Disable
*/
__CONFIG(INTIO & WDTDIS & PWRTEN & MCLRDIS & UNPROTECT \
& UNPROTECT & BORDIS & IESODIS & FCMDIS);// Using Internal Clock of 8 MHz
#define FOSC 8000000L#define MAX_COUNT 200
#define MAX_TMR0 0xFB
#define MAX_DEBOUNCE 0x0A
#define MAX_TBLINDEX 0x0Aunsigned char pwm_count=0;
unsigned char pwm_m1=0;
unsigned char pwm_m2=0;
unsigned char tablepwm1[10]={0x10,0x5A,0x9A,0x20,0x40,0x8A,0x82,0x30,0x58,0xAA};
unsigned char tablepwm2[10]={0x70,0x8A,0x2A,0x30,0x1C,0x2A,0x4B,0xA0,0x18,0x2A};
unsigned char tableindex=0;/* The Delay Function */
#define delay_us(x) { unsigned char us; \
us = (x)/(12000000/FOSC)|1; \
while(--us != 0) continue; }void delay_ms(unsigned int ms)
{
unsigned char i;
do {
i = 4;
do {
delay_us(164);
} while(--i);
} while(--ms);
}static void interrupt isr(void)
{
if(T0IF) { // TIMER0 Interrupt Flag
pwm_count++; // PWM Count Increment
if (pwm_count >= MAX_COUNT) {
pwm_count=0;
GPIO1=0; // Turn off GP1
GPIO2=0; // Turn off GP2
}if (pwm_count == pwm_m1) {
GPIO1=1; // Turn On GP1
}
if (pwm_count == pwm_m2) {
GPIO2=1; // Turn On GP2
}
TMR0 = MAX_TMR0; // Initial Value for TIMER0 Interrupt
T0IF = 0; // Clear TIMER0 interrupt flag
}
}void main(void)
{
unsigned char mode,keycount;OSCCON=0x70; // Select 8 MHz internal clock/* Initial Port Used */
TRISIO = 0x39; // GP1 and GP2 Output, GP0,GP3,GP4 and GP5 as Input
CMCON0 = 0x07; // Turn off Comparator (GP0, GP1, GP2)
GPIO = 0x00; // Turn Off all IO/* Init ADC Peripheral */
ANSEL = 0x79; // Set AN0 (GP0) and AN3 (GP4) as Analog Input, Internal Clock/* Init TIMER0: TIMER0 Period = 1/FSOC x 4 x Prescale x TMR0*/
OPTION = 0b00000000; // 1:2 Prescale
TMR0=MAX_TMR0 ;/* Init Variable Used */
pwm_count=0;
pwm_m1=0;
pwm_m2=0;
mode=0;
keycount=0;
tableindex=0;GIE =1; // Enable Global Interrupt
for(;;) {
// Display the LED
if (GPIO5 == 0) {
keycount++;
if (keycount > MAX_DEBOUNCE) {
keycount=0;
mode = mode + 1;
if (mode > 2) mode = 0;if (mode >= 0x01) {
T0IE = 1; // Enable TIMER0 Interrupt on Overflow
} else {
T0IE = 0; // Disable TIMER0 Intterupt on Overflow
pwm_count=0;
pwm_m1=0;
pwm_m2=0;
GPIO1=0; // Turn off GP1
GPIO2=0; // Turn off GP2
delay_ms(500);
}
}
}if (mode == 1) {
/* Read the ADC here */
ADCON0=0b00000001; // select left justify result. ADC port channel AN0
GODONE=1; // initiate conversion on the channel 0while(GODONE) continue; // Wait for ldr_left conversion done
pwm_m1=ADRESH; // Read 8 bits MSB, Ignore 2 bits LSB in ADRESLdelay_ms(1);/* Read the ADC here */
ADCON0=0b00001101; // select left justify result. ADC port channel AN3
GODONE=1; // initiate conversion on the channel 4while(GODONE) continue; // Wait for ldr_left conversion done
pwm_m2=ADRESH; // Read 8 bits MSB, Ignore 2 bits LSB in ADRESL
delay_ms(1);
}if (mode == 2) {
pwm_m1=tablepwm1[tableindex];
delay_ms(10);
pwm_m2=tablepwm2[tableindex];
delay_ms(10);
tableindex++;
if (tableindex >= MAX_TBLINDEX)
tableindex = 0;
}
}
}/* EOF: laserlight.c */Generating the PWM (Pulse Width Modulation)
The simple way to generate the PWM output is to take advantage of the PIC12F683 microcontroller PWM build in feature, but because the PIC12F683 only support one PWM output therefore we need to find a way to imitate this peripheral behavior in the firmware. Most of microcontroller PWM peripheral use TIMER peripheral to generate the pulse; in the PIC12F683 the PWM generator use the TIMER2 to generate the PWM output (CCP1) as shown on this following picture:
When TIMER2 start counting, the value of the TMR2 register (TIMER2 counter register) is constantly compared to both the PR2 and CCPR1L registers. When TMR2 equal to CCPR1L value the CCP1 output will be reset and when TMR2 equal to PR2 value it will set the CCP1 output. Therefore by changing theCCPR1L register value as shown on the picture above, we could change the PWM duty cycle (pulse width). You could read more about the principal of using the PIC microcontroller PWM peripheral on my previous posted blog H-Bridge Microchip PIC Microcontroller PWM Motor Controller.
Using the same principal I made the PWM generator in firmware base on the Microchcip PIC12F683 microcontroller TIMER0 peripheral as this following block diagram:
The basic principal of the TIMER0 base PWM generator is to use the TIMER0 overflow interrupt to increase our PWM counter variable pwm_count and if this variable reaches the MAX_COUNT (200) then we will reset both the GP1 and GP2 output pins. If not then we will compare it with the PWM duty cycle control variables pwm_m1 and pwm_m2, if equal then we simply set the GP1 or GP2 output pins. Using this principal now we could easily generate an efficient PWM signal base on the PIC12F683 microcontrollerTIMER0 peripheral.
Now take a look at the PIC assembler code that implements the PIC12F683 microcontroller TIMER0peripheral base PWM generator:
; Check the TIMER0 Interrupt here
btfss INTCON,T0IF
goto ExitISR ; If (T0IF != 1) then Exit ISR
bcf STATUS,RP0 ; Select Registers at Bank 0
incf pwm_count ; pwm_count++
movlw MAX_COUNT
subwf pwm_count,w ; if (pwm_count < MAX_COUNT) then CheckPWM
btfss STATUS,C ; else clear GP1 and GP2
goto CheckPWM
bcf GPIO,GP1 ; GPIO1=0
bcf GPIO,GP2 ; GPIO2=0
goto ExitPWMThis routine first examine if this interrupt is generated by TIMER0 peripheral by checking the T0IF bit on the INTCON register, if this interrupt come from TIMER0 then the T0IF bit will be set (logical “1“) then we continue to increase the pwm_count variable and if it reach the MAX_COUNT we reset the GP1 andGP2 output pins. Next if the pwm_count is not reaches the MAX_COUNT, then compare its value to thepwm_m1 and pwm_m2 variables as shown on this following code:
CheckPWM:
movf pwm_m1,w
subwf pwm_count,w
btfsc STATUS,Z ; if (pwm_count == pwm_m1) then Set GP1
bsf GPIO,GP1 ; Set GP1 Bit
CheckM2:
movf pwm_m2,w
subwf pwm_count,w
btfsc STATUS,Z ; if (pwm_count == pwm_m2) then Set GP2
bsf GPIO,GP2 ; Set GP2 bitWhen the pwm_count equal to pwm_m1 or pwm_m2 then we set (logical “1“) each of the GP1 andGP2 output pins.
To calculate the PWM period, first we have to calculate the TIMER0 period using this following formula:
TIMER0 Period = 1/Fosc x 4 x Prescale x (TMR0 + 1)
In this tutorial we use 1:2 prescale, TMR0 = 251 (0xFB) and 8 MHz internal oscillator, therefore theTIMER0 will be interrupted every:
TIMER0 Period = 1/8000000 x 4 x 2 x (256 - 251) = 0.000005 second
Every time the TIMER0 interrupted (TMR0 overflow), we will increase the pwm_count variable until it reach the MAX_COUNT (200), then we will reset each of the GP1 and GP2 output pins. Therefore the approximately PWM period could be calculated as follow:
PWM Period = MAX_COUNT x 0.000005 seconds = 200 x 0.000005 = 0.001 second
PWM Frequency = 1 / T = 1/0.001 = 1000 Hz = 1KHz
PWM Frequency = 1 / T = 1/0.001 = 1000 Hz = 1KHz
Changing the DC Motor Speed
This laser projector project has two mode for controlling both of the DC motors speed, the first one is to use the trimports (VR1 and VR2) where we read the voltage level produce by these trimports (voltage divider circuit) using the PIC12F683 microcontroller Analog to Digital Converter (ADC) peripheral, then apply these ADC values to change each of the DC motor speed. The second one is to use the fixed value stored in the lookup table and then assign these values to change each of the DC motor speed.
The Microchip PIC12F683 microcontroller has four ADC channels available; on this project we use the channel 0 (AN0) and the channel 4 (AN3). By choosing the require ADC channel on the ADCON0 register (the ADC control register) and selecting the left justify result (ADFM=0) we could read the voltage value produced by each of the VR1 and VR2 trimports in ADRESH register and assign these value to pwm_m1and pwm_m2 variables as shown on this following PIC assembly code:
ShowMode1: ; Used ADC for PWM
movlw B'00000001' ; Left Justify and turn on the ADC peripheral, channel 0 (AN0)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 0 (AN0)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Loop
call Delay1msmovlw B'00000001' ; Left Justify and turn on the ADC peripheral, channel 0 (AN0)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 0 (AN0)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Loop
movf ADRESH,w ; Conversion Done, Read ADRESH
movwf pwm_m1 ; pwm_m1 = ADRESH
call Delay1ms
movlw B'00001101' ; Left Justify and turn on the ADC peripheral, channel 3 (AN3)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 3 (AN3)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Test
call Delay1msmovlw B'00001101' ; Left Justify and turn on the ADC peripheral, channel 3 (AN3)
movwf ADCON0 ; Vreff=Vdd
bsf ADCON0,GO ; Start the ADC Conversion on channel 3 (AN3)
btfss ADCON0,GO ; while(GO == 1)
goto $-1 ; Keep Test
movf ADRESH,w ; Conversion Done, Read ADRESH
movwf pwm_m2 ; pwm_m2 = ADRESH
call Delay1ms
goto KeepLoopFor more information about using the PIC ADC peripheral you could read my previous posted blog PIC Analog to Digital Converter C Programming.
Next is the automatic mode, this mode will assign the predetermined value for each PWM value on the PIC program flash. By using the PIC assembler “retlw k” (return literal value k on the W register) instruction we could easily retrieve these values. The following PIC assembly code shows how we do it:
ShowMode2: ; Used Predefined Value for PWM
movf tableindex,w
call tablepwm1 ; Call tablepwm1
movwf pwm_m1 ; Assigned it to pwm_m1
movlw .30
call DelayMs ; DelayMs(30)
movf tableindex,w
call tablepwm2 ; Call tablepwm2
movwf pwm_m2 ; Assigned it to pwm_m2
movlw .30
call DelayMs ; DelayMs(30)
incf tableindex ; tableindex++
movlw MAX_TBLINDEX
subwf tableindex,w
btfss STATUS,C ; if (tableindex >= 0x0A) then tableindex = 0
goto KeepLoop
clrf tableindex ; tableindex = 0
...
...
; Predefined value table for Automatic PWM
tablepwm1:
addwf PCL,f
retlw 0x10
retlw 0x5A
retlw 0x9A
retlw 0x20
retlw 0x40
retlw 0x8A
retlw 0x82
retlw 0x30
retlw 0x58
retlw 0xAAtablepwm2:
addwf PCL,f
retlw 0x70
retlw 0x8A
retlw 0x2A
retlw 0x30
retlw 0x1C
retlw 0x2A
retlw 0x4B
retlw 0xA0
retlw 0x18
retlw 0x2AThe principal here is to modify the PCL (program counter loading) register. The PCL is the PIC12F683 microcontroller program counter least significant byte and together with the PCLATH register forming the PIC12F683 microcontroller 13-bits wide program counter. The “goto” command behavior could be achieved by manipulating the PCL content, for example:
movlw 0x01
call tablepwm2
noptablepwm2:
addwf PCL,f
retlw 0x70
retlw 0x8A
retlw 0x2AWhen the PIC microcontroller run the “call tablepwm” instruction then it immediately change the program counter (PCL) to the program address pointed by “tablepwm2” label which is the “addwf PCL,f” instrunction. When the PIC microcontroller execute this instruction it will add the content of Wregister (0×01) to the PCL register and the PIC microcontroller immediately jump to the “PCL + 0×01” program address. Next it will execute the “retlw 0×8A” instruction and it simply return to the caller with0×8A value on the W register.
Therefore by increasing the tableindex (the lookup table pointer) variables we could easily assigned the predetermined value on each of the pwm_m1 and pwm_m2 variables.
The basic of PIC Assembly if condition
One of the confusing part in understanding the PIC assembly instruction especially for the beginner is “how to implement the if condition” in the assembly code. In this laser projector project PIC assembly code you noticed that it use quite a lot of “if condition” in order to make it work. The basic of PIC assembler “if condition” could be constructed using this following first template code:
movf var_1,w ; w = var_1
subwf var_2,w ; w = var_2 - var_1
btfss STATUS,C ; if (var_2 >= var_1) goto label_2
goto label_1 ; else goto label_1
goto label_2The first code (movf var_1,w) instructs the PIC microcontroller to put the content of var_1 into the W(working) register. The second code (subwf var_2,w) instructs the PIC microcontroller to subtract the content of var_2 variable with the content of W register and put the result in the W register or we could write down as:
W = var_2 - var_1The third code (btfss - bit test f register, skip if set) instructs the PIC microcontroller to examine if the C(carry) bit in the STATUS register is set (logical “1“), if it set then skip one instruction (the PIC microcontroller actually will automatically replace the next instruction goto label_1 with the nopinstruction) and it will execute the “goto label_2” code. If the C bit is clear (logical “0“) then it will execute the “goto label_1” code.
The C (carry) bit in STATUS register will always set (logical “1“) if the value of var_2 variable is greater or equal to var_1 variable. Next, the second “if condition” template is shown on this following code:
movf var_1,w ; w = var_1
subwf var_2,w ; w = var_2 - var_1
btfss STATUS,Z ; if (var_2 == var_1) goto label_2
goto label_1 ; else goto label_1
goto label_2This time we will examine the Z (zero) bit in the STATUS register, The Z (zero) bit will always set (logical “1“) when the var_2 value equal to var_1 value. Last, the third “if condition” template is shown on this following code:
movlw 0x08 ; w = 0x08
subwf var_1,w ; w = var_1 - 0x08
btfss STATUS,C ; if (var_1 >= 0x08) goto label_2
goto label_1 ; else goto label_1
goto label_2This third template is just a variation of the first template, this time we load the literal value 0×08 on theW register and compare it with the var_1 variable. By using just these three “if condition” templates, you could easily implement many types of the “if condition” in your code. The key to understand and implement the PIC assembly “if condition” instruction successfully in your code is to use these templates consistently, once you understand than you could modify or combine it with the btfsc (bit test f register,skip if clear) instruction or any PIC assembler instruction that effecting the C and Z bits in the STATUSregister to make your assembly code more efficient.
To make the PIC assembly code easier to understand, in this laser projector tutorial I put many comments in the code and you could also compare it with the equivalent C language code provided for this project. The C language code uses the same variable name as in the PIC assembly code for easier comparison purpose.
Inside the PIC Assembler Code
The laser projector project use the PIC12F683 microcontroller TIMER0 and ADC peripheral to control each of the DC motors speed. These following instructions are used to initial the PIC12F683 peripherals:
Main:
bsf STATUS,RP0 ; Select Registers at Bank 1
movlw 0x70
movwf OSCCON ; Set the internal clock speed to 8 MHz
movlw 0x39 ; GP1 and GP2 Output, GP0,GP3,GP4 and GP5 as Input
movwf TRISIO ; TRISIO = 0x39
bcf STATUS,RP0 ; Select Registers at Bank 0
movlw 0x07
movwf CMCON0 ; Turn off Comparator (GP0, GP1, GP2)
clrf GPIO
; Now we Set the ADC Peripheral
bsf STATUS,RP0 ; Select Registers at Bank 1
movlw 0x79 ; Set AN0 (GP0) and AN3 (GP4) as Analog Input
movwf ANSEL ; Using the Internal Clock (FRC)
; Now we set the TIMER0 Peripheral
; TIMER0 Period = 1/FSOC x 4 x Prescale x TMR0
movlw 0x00 ; Use TIMER0 Prescaler 1:2, Internal Clock
movwf OPTION_REG ; OPTION_REG = 0x00bcf STATUS,RP0 ; Select Registers at Bank 0
movlw MAX_TMR0
movwf TMR0 ; TMR0=MAX_TMR0
; Initial the variables used
clrf mode ; Default mode = 0, Light Show Off
clrf pwm_count ; pwm_count = 0
clrf pwm_m1 ; pwm_m1 = 0
clrf pwm_m2 ; pwm_m2 = 0
clrf keycount ; keycount = 0
clrf tableindex ; tableindex = 0; Activate the Interrupt
bsf INTCON,GIE ; Enable Global InterruptThe first instruction is to set the OSCCON (oscillator control) register to use the 8MHz internal clock, next we set the TRISIO (the three state I/O controller buffer) register for the input and output port and turn off the comparator peripheral on CMCON0 (comparator control) register. After resetting the GPIO (general purpose I/O) register we continue to setting the ANSEL (analog select) register for the ADC peripheral and OPTION_REG for the TIMER0 peripheral and initial all the variables used in the program by clearing them.
Right before entering the infinite loop we activate the GIE (global interrupt enable) bit in the INTCON(interrupt control) register so the TIMER0 interrupt could occur when the TMR0 (TIMER0 counter) register overflow (more than 255).
Inside the infinite loop (the MainLoop label), we continuously checked the mode variable; the modevalue is used to determine the program behavior. When the mode value is 0 then the program simply continuously loop, when the mode value is 1 then the program will use the ADC value to control each of the DC motor speed and when the mode value is 2 then the program will use the look-up table to control the PWM signal (automatic mode).
The PIC Assembly Code and the C Code Comparison
Since in this project I use the PIC Assembly language and the C language for the firmware; it would be interest to compare both the HEX program sizes. The following is the HEX code produced by the Microchip PIC Assembler and HI-TECH C PRO (Lite Mode) compiler.
The HEX code produce by the HI-TECH C PRO compiler is 356 Word (623 Byte) in “Lite Mode“, but if the C code is compiled in “PRO Mode” the size will be 40% smaller or it’s about 214 Word (374.5 Bytes), on the other hand the Microchip Macro Assembler produce 180 Word (315 Bytes) for the HEX code. Now you could see, that if we use the professional C language compiler it could produce a very small HEX code where it almost equal to the HEX code produced by the Assembly language.
Downloading the HEX Code
After compiling and simulating your code it’s time to download the code using the Microchip PICKit3 programmer, connect the PICKit3 ICSP (Microchip In Circuit Serial Programming) port to your PIC12F683 microcontroller pins then from the Programmer menu Select Programmer -> PicKit3 and the select theProgrammer -> Program menu to download your HEX code into the PIC12F683 microcontroller flash.
Now it’s time to enjoy the laser projector project presented in this following video:
The Final Though
In this laser projector project both the PIC Assembly and C code demonstrate that the 2048 bytes of the 8-bit Microchip PIC12F683 microcontroller flash is still adequate to handle more advanced application such as the PICAXE-08M microcontroller from the Revolution Education Ltd, this microcontroller is based on the Microchip PIC12F683 microcontroller and they put a powerful BASIC (Beginners for All Purpose Symbolic Code) interpreter inside, so the PICAXE-08M could be used as a complete development framework for the embedded system application. You could read more information about the PICAXE microcontroller in my previous posted blog Introduction to the embedded system with PICAXE microcontroller.
Using the TIMER peripheral to generate the PWM signal as shown on this project could be applied to almost any microcontrollers available today. The basic principal shown here also could be easily modified to drive the multiple servos output as the servo use the PWM signal to control its movement.
No comments:
Post a Comment